Hybrid is not any new jargon. It is an existing technology and I still wonder why it is not being used extensively. Now there is a real hoopla surrounding the term hybrid. If you are an avid motor enthusiast it should not surprise you. Hybrid concept has been tried for a long period of time using a combination of gasoline and battery power.

Some tried with nickel-cadmium combination and some even opted for the pricey lithium ion batteries. Both these combinations were of no avail. You need to have a hybrid which could be mass produced and at the same time it should not burn your pocket.

Hybrid which uses water is the only solution. Hybrid which has the ability to extract Oxydrogen from a combination of tap water and baking soda could be termed as the ideal hybrid. Such a hybrid which would use water as the fuel would produce only water as Oxydrogen burns effortlessly giving the much needed energy for the vehicle and the product is plain water. No wonder, hybrid using water has now become the perfect choice. It really has become obvious.

Hybrid using water could be created with out any structural changes to your existing gasoline system. All you need to do is create an apparatus which can draw electricity from the cars’ battery and use it to split the mixture containing water and baking soda. Water Hybrid cars are easy to build and they are far more economical compared with their battery counterparts.

Find Out Now How You Can Drive Around Using WATER as FUEL and Laugh At Rising Gas Costs. Convert Gas To Water is the place to visit.

If you ponder over this question, you will get a variety of replies. Some would advise you to shut down the vehicle when it is not in motion. Some would even convince you to push your own vehicle so that you will get the maximum mileage! There are a variety of ways to do it. But there is only one concrete way of improving your mileage. Turn your car into a hybrid and you can get real extra mileage. Hybrid is the only real way of attaining it; everything else is just a compromise.

You can use a hybrid plug-in which is nothing but an accessory. This accessory which has the ability to produce Oxydrogen which is a product create by the splitting up of water and baking soda is capable enough to increase your mileage by nearly 50%. Once you design or build such an accessory which is capable of producing Oxydrogen, your engine would draw energy from both Oxydrogen and Gasoline. This is the best way of achieving the maximum amount of savings. Switching off your engine which is not in motion and braking less may save some little bit of gasoline. But, it can never be compared with the saving which your car would give when you convert your gasoline powered car into a Hybrid.

Hybrid kit is not any another accessory. It is the future, accept it and embrace it. You will never regret for converting your vehicle into a hybrid. In course of time your hybrid will save for itself.

Find Out Now How You Can Drive Around Using WATER as FUEL and Laugh At Rising Gas Costs. Convert Gas To Water is the place to visit.

Hybrid cars are the need of the hour. Soaring gas prices have forced both the manufacturers as well as the consumers to turn towards Hybrid cars. Hybrid car normally uses energy from two sources. To convert your existing car into a hybrid car, you need to analyze certain factors. You need to produce a gas called HHO. HHO is commonly referred as Brown\’s gas or Oxydrogen.

Oxydrogen can be generated by making use of the electricity generated from the car\’s battery. The energy generated by HHO is significant and it burns with out any hassle. The end product is water and not any harmful gas.

You can create your own little kit to turn your car into a hybrid. All you need is a quart size container. The container needs to be filled with a mixture of baking soda and tap water. The container needs to receive the power from the engine. The electricity generated would be used to convert the mixture into HHO gas. Then it needs to divert the produced HHO to the carburetor. As a result your car would have turned into a Hybrid. You can easily get these items in your hardware store. This is just an add-on kit. So there is no need you got to worry about the warranty of the car.

I guarantee you there would not be any damage to the engine. You just need to find the right items in your nearby hardware store and the store owner would be happy to provide you the key items. Go ahead and turn you car into a hybrid. In course of time, your Hybrid would pay for itself.

Find Out Now How You Can Drive Around Using WATER as FUEL and Laugh At Rising Gas Costs. Convert Gas To Water is the place to visit.

Hybrid car runs on the energy generated from the gasoline as well as battery. Now it is relatively simpler to turn your car into a hybrid by making use of water. There is no need you got to invest on costly lithium batteries anymore. We can easily assemble a kit which would generate us Oxyhydrogen. Oxyhydrogen is powerful enough to make your hybrid vehicle move.

The key is in creating an apparatus which has the ability to produce Oxyhydrogen with the passage of electricity generated from the battery of the car. You need to have a apparatus filled with tap water and baking soda. When electricity is passed through such a mixture, it generates the much needed Oxyhydrogen. Oxyhydrogen needs to be passed through the carburetor and as a result you will get a hybrid car. In order to convert your car into a hybrid which would run on water, you need to possess some basic design skills and a trip to the local hardware store is a must.

Once you can create a plug-in which would generate the much needed Oxyhydrogen, everything else would follow by itself. This is just an add-on feature and it should not be confused as a replacement feature. In future there may be techniques in which you can solely rely on water for your hybrid car, as of now you need to contend with a car which is powered by a mixture of water and gasoline. As water is the end product, hybrid saves gasoline as well as the environment.

Find Out Now How You Can Drive Around Using WATER as FUEL and Laugh At Rising Gas Costs. Convert Gas To Water is the place to visit.

The concept of winching has remained relatively simple for so many years: you turn it on, it pulls, and you find yourself extricated from whatever mess you found yourself in as a result of harsh terrain.

But now thanks to recent developments and improvements to existing recovery hardware, off road enthusiasts find themselves with a bevy of new and exciting choices in recovery tools, such as some of the exclusive features and developments of Mile Marker and Warn Winches.

Thermometric Indicator
A thermometric indicator is an industry first in high performance winching control. As of yet, it is only available on one model of Warn winch, but its growing success could bring about further inclusion of this feature in future models.

At its core, a thermometric indicator provides you with operator feedback regarding motor temperature during winching. In essence, this allows you to regulate your winch operation with a level of control not yet achieved by most diagnostic tools.

As a result, the thermometric indicator works in conjunction with a custom winch motor to produce the perfect balance of torque and pulling speed, all at a safe and efficient temperature.

MOSFET Technology
Metal Oxide Semi-Conductor Field Effect Transistor (MOSFET) technology is a growing standard among winches for serious off road enthusiasts. These precision-engineered control modules offer unprecedented electromechanical function for regulating winch operation.

A MOSFET control module essentially eliminates the winch solenoid pack, effectively minimizing voltage drop while also managing heat gain to keep it at a safe level. The end result is an energy efficient and reliable winch system optimized for the serious user.

Air Compressor
An air compressor is an all-purpose tool that many that off road enthusiasts find come in handy during those off road expeditions. Whether you need to air up some tires after a low pressure crawl or power air tools to make some on-the-fly tweaks to your vehicle, air compressors offer a variety of uses on off road trails.

Now thanks to some clever minds, certain winch systems have been combined with portable air compressors, offering an efficient one-two punch for convenience. Most notably, the Powerplant series of Warn winches are equipped with this feature.

It\’s a simple concept, really. But in the end, having the functionality of both an air compressor and winch in the same unit provides numerous benefits to make sure you\’re equipped and fully-prepared to take on off road terrain.

Value Series
It\’s a simple concept, really. But in the end, having the functionality of both an air compressor and winch in the same unit provides numerous benefits to make sure you\’re equipped and fully-prepared to take on off road terrain.

Smittybilt is one manufacturer that has an offering in this category. The value series of Warn winches is another option. Regardless of what you choose, value winch systems represent an inexpensive way to get the recovery tools you need from top name brands.

Billy Han is a Web Copywriter for Transamerican Auto Parts, a leading supplier of tires, wheels, lift kits, winches, and more.

Transamerican Auto Parts is your source for all recovery equipment, including Warn winches, Mile Marker winches, and a number of other winch-related accessories.

A very common way to diagnose and tune-up a modified or racing engine is by looking the spark plug firing tips because its appearance can reveal if your engine has a problem that need correcting. But you need to be aware that the same spark plug firing tips appearance can have different root causes:

A) Mixture or timing misadjustment or other possible mechanical troubles.

B) High performance modifications that increase the horse-power level, augmenting therefore the combustion chambers temperature and stress at high RPM.

C) Colder racing spark plugs fouling at idle, stop and go, and lower speeds.

Unfortunately, for each spark plug firing tip appearance, the traditional spark plug troubleshooting charts only are considering as possible trouble causes the first list A.

But in high performance modified engines and racing applications, the list B is usually the main cause of the higher temperatures in the combustion chambers that generates overheating, pre-ignition and detonation; and the list C is the main cause of fouled spark plugs that generates misfiring, hard starting, black smoke and great loose of power.

In spite of that fact, carefully review of almost all the troubleshooting charts, reveals that the causes of the B and C lists are not included, or at least mentioned. However when talking on the high performance field, these causes are with extreme frequency the main guilty of most of the troublesome spark plug firing tip appearance.

As result of this lack of information, never was sufficiently clear that the undesirable spark plug firing tip might be attributable to an inappropriate spark plugs heat range. Either never was mentioned strongly enough the transcendent importance that have to customize the spark plugs heat range, so it was never taken into account.

Forasmuch it should not surprise that even experienced engine builders, modifiers and tuners often confuse an overheated spark plug caused by the new level of power at high RPM, with a lean mixture trouble, because the appearances of its firing tip look exactly the same; making wrong diagnostics, and enriching the mixture, instead of customize the heat range to the engine\’s power.

And worst, when the heat excess level provokes pre-ignition or detonation (which is very frequent due to the high levels of demands that the racing engines are submitted) most of the times the traditional troubleshooting charts are guiding them erroneously to believe that their engines are having some mechanical troubles and therefore they are engaging unnecessarily in repair nonexistent mechanical problems, like cooling system failure: or to suppose that it is owed to a mixture or timing misadjustment, consequently enriching the mixture and/or retarding the ignition timing, arriving inclusive to decrease the boost pressure, the nitrous flow, the compression ratio, etc. losing by this way tons of power, instead of the unique right, simplest, fastest and cheapest solution that is to customizing the spark plug heat range to the huge power, stress and heat achieved at high RPM.

Due to the same absence of information, they can not either distinguish when the cold racing spark plugs are fouling at idle, stop and go, and lower speeds, from when has a rich mixture, because both have the same carbon fouled firing tips appearance; and what is still worst, they can not either distinguish when the colder racing spark plugs for heavily modified engines are fouling at idle, stop and go, and lower speeds, from when the engines has worn-out piston rings and cylinders, because both have the same oil fouled firing tips appearance.

Those wrong diagnostics are leading them to wrong solutions: trying to adjust unnecessarily the air-fuel mixture when they see carbon fouled spark plugs, and being bottled without need in overhauling the engine to repair mechanical troubles that do not exist, when they see oil fouled spark plugs, instead of avoiding idle and lower speeds in engines built for run at high RPM, or to customize the spark plug heat range for these type of show off usage.

Also when the traditional spark plug troubleshooting charts mention “wrong heat range” or “check for the correct heat range”, because it is not enough clear, a great majority of they are quite familiarized with the concept that “wrong heat range” only could be a spark plug different than the stock or the suggested by the manufacturers, ignoring that they should switch the spark plug\’s heat range.
And, as if was not sufficient with this confusion with the information, until very short time did not exist method neither tool to perform the important task of customize the heat range of the sparkplug, according to any specific high performance modification level, so, the election of the aftermarket sparkplug that best works at any RPM load or stress, was left to the intuition, experience and the criterion of each technician, who only had the unfriendly guesswork of never-ending trial and error proofs, testing different spark plug sets, with inexact and risky results.

But the racing field is no place for mistakes.

Is for that reason that the traditional troubleshooting charts are not the most adequate guide to properly and accurately diagnosing your expensive high performance modified or racing engine, risking you to lose your engine and that is still worse, to lose the race.

What is then the right way to correctly diagnose the spark plugs in the high performance field?
Be sure that, if you are not having real mechanic problems, you must check the heat range of the installed spark plugs, and select the replacement with the colder heat range better suited to your exactly high performance modification level.

Is it a hard work? It depends. If you are using the right tool, that allows you to see, confirm, verify, select, and choose the exact heat range you must install in your high performance modified engine, it is a piece of cake!

Of course if not….. it could be unending, unfriendly, blind and risky guesswork.

You decide!

www.determinator.net

Elena Maria DB Orsos, is President & CEO of Smart Racing Tools USA and Racing Technologies. Her invention patents in the automotive field, with demonstrated value to increase power to high performance modified engines, and to improve performance and mileage to standard and daily use cars, and to decrease emissions, makes her a very well respected name in these aspects. She was nominated to international prizes due to her innovations and is frequently invited as speaker to international automotive and environmental events.

For more information visit the above web site.

Many people have been wondering of how to increase gas mileage in order to same some money on filling the gas tank. There have been many tips circulating around and recently, I have written several ways to increase gas mileage. Some people have asked me some questions. So, I think I should write out some of the main concerns here.

1) Will inflating the tires make it difficult to drive and is it dangerous?
Yes, it is indeed true that over-inflating the tires will affect the handling of the car. Therefore, you shouldn\’t inflate the tires too much and you should test drive before really drive on the main roads. Besides, over-inflating the tires may lessen the life of the tires, so remember to check your tires frequently.

2) Can I really increase the gas mileage by 20%?
Many people have asked me this. I will confidently say yes, you can increase your car\’s gas mileage by 15-20% if you follow all the steps I have provided. Besides, remember to service your cars, clean the air filter et cetera. These will also helps to increase gas mileage. If you want better or more noticeable effect, you may try some products that increase gas mileage such as special synthetic motor oil or even modify your car engine to increase the efficiency of the engine, however, this may cost some money.

3) How long does it take to see the effect?
Duh… You will see the effect instantly if you do everything today. Lol, I\’m stunned to see this question.

The above are the FAQ that some people have asked me recently. Hope that it helps. You can also find other ways to increase gas mileage at the website below.

If you are willing to save more money by putting in some effort, you can find out more information on how to increase gas mileage at the website here : http://www.squidoo.com/run-a-car-on-water

This is not a catchy title to garner your attention instead this article is about the real alternative which can make our earth a better place to live. Hybrid is the next logical step for every vehicle on earth which runs on gasoline. Hybrid has evolved from using battery to now water. I am sure the proven technology is fully exploited so that we can run on water. Let us look deeper into this real alternative called Oxydrogen which can be extracted from water.

Oxydrogen is a very powerful energy source and you can extract it through passage of electricity into a mixture of tap water and baking soda. Once Oxydrogen is produced it needs to be channelized so that it can pass through the carburetor. Oxydrogen is energy rich and your hybrid kit would not pose any problem whatsoever. Hybrid kit is just a plug-in and you are not making any changes to the engine. So there would not be any hassles with your manufacturer if you use a hybrid kit. You are actually increasing the life time of your engine. So why would anyone be angry?

Hybrid which uses Oxydrogen is the real future. Hybrid vehicles would make every country self-sufficient. As of now, a hybrid vehicle depends on a combination of energy generated form gasoline as well as Oxydrogen. In course of time, there would be hybrid vehicles which no longer would require gasoline but would run solely on water. All I know is that day cannot come soon enough.

Find Out Now How You Can Drive Around Using WATER as FUEL and Laugh At Rising Gas Costs. Convert Gas To Water is the place to visit.

Why not? I am not going to explain you any rocket science. The Hybrid technology which I am going to explain is nearly 90 years old. I really wonder why Hybrid has not been unearthed much before. World is getting polluted everyday by gasoline engines and I am very sure that there is no single engine on earth which solely depends on water. But, we can develop an engine which would sparingly use gasoline and hardly pollute the earth.

Allow me to explain it in detail. Oxydrogen is present in water. It is more powerful than gasoline. The key is in extracting Oxydrogen from water using your Hybrid kit. Through passage of electricity into a mixture containing baking soda and ordinary tap water, you can unleash the potent Oxydrogen from water. The trick is to channelize the Oxydrogen into the carburetor

You can easily create a hybrid kit by visiting your hardware store. Hybrid would not only save you on your gas bills abut also it would increase the life of your engine. Hybrid makes the maximum use of gasoline as well as water. Your ordinary gasoline makes use of only 20% of your fuel for pulling your vehicle the remaining 80% is wasted in the form of smoke and vibrations.

By running your hybrid on water, the only product which comes out of burning Oxydrogen is water. No more, green house gases from our exhaust pipes. Let us go green and save the environment. Saving money and the environment: Now that is a combination I like.

Find Out Now How You Can Drive Around Using WATER as FUEL and Laugh At Rising Gas Costs. Convert Gas To Water is the place to visit.

In these days of growing pollution, it is our duty to do something for the environment. Cars are our inevitable modes of transportation and we can not go back to the olden days of horse-carts for the sake of environment as it would hamper our progress. Instead, we can turn our vehicle in to a hybrid and reduce the pollution coming out of our cars.

Hybrid is a combination of two energy resources. Apart from gasoline, it may draw its energy from Battery or it may draw its energy from water. To make it draw energy from water, you just need to develop a plug-in which would work in tandem with your gasoline engine.

Hybrid kit can be easily created as the technology which we are going to depend is nearly 90 years old and a well proven one. You need to collect the required materials from your hardware store so that you can create a hybrid kit. You need to install a container which can contain the mixture of baking soda and tap water. It needs to draw the energy from the battery and create the vital Oxydrogen which would pass through the carburetor supplying the much needed energy. Concept is simple and it is up to your design to make it convenient.

Hybrid is certainly the way to go in to the future. Once you do convert your car into a water driven hybrid, you are not only saving gas but also the environment. Go ahead and turn green.

Find Out Now How You Can Drive Around Using WATER as FUEL and Laugh At Rising Gas Costs. Convert Gas To Water is the place to visit.